You open Epson Scan 2 to scan a document and the scanner list is empty. Your printer prints fine over Wi-Fi, but the scanning software cannot see it. This is a common Epson network problem and it is rarely a hardware failure.
Usually the cause is a simple communication breakdown between your computer, router, and scanner. A changed IP address, a firewall rule, or devices on different networks can break scanning even though printing works. Work through the fixes below in order.
Quick Answer
Restart your printer, computer, and router, and make sure all are on the same network. Open Epson Scan 2 Settings, delete the old scanner entry, and add it again using the printer’s current IP address from its network status sheet. If it still fails, allow Epson Scan 2 through your firewall and reinstall the full driver package.
Why Epson Scan 2 Loses the Scanner
Printing and scanning use different network services. Your computer can send a print job while Epson Scan 2 searches for the scanner using a discovery service. If discovery is blocked, printing may survive but scanning disappears.
Common causes
- Printer and computer are on different networks, such as a main and a guest network
- Router assigned a new IP address after a restart or power cut
- Firewall or antivirus software is blocking Epson Scan 2
- Old or incomplete driver installation after an operating system update
- VPN software is routing local traffic outside your home network
- The scanner list still points to a USB or previous network entry
Step 1: Check the Basics First
Confirm the printer is online and healthy before changing settings. A printer in an error state or disconnected from Wi-Fi will never appear in Epson Scan 2.
- Print a test page from the printer control panel. If it fails, fix the printer connection first.
- Check the Wi-Fi icon on the printer display. It should show connected, not flashing or crossed out.
- Wake the printer from sleep and wait 30 seconds.
- Restart the printer completely, then restart your computer.
- Try scanning again before changing anything else.
A clean restart fixes many temporary discovery failures after a router update or a brief power cut, so always test again at this point.
Step 2: Confirm Both Devices Are on the Same Network
Your computer and printer must be on the same local network. Modern homes often have several networks with very similar names, and a small difference matters.
Print a Network Status sheet from the printer’s Settings and Network menu. Compare the network name word for word with the Wi-Fi name on your computer. If one device is on a guest network or an extender network with a different name, move it to the main network.
Disconnect any VPN while you test. A VPN can hide local scanners even when browsing works. If scanning works with the VPN off, enable split tunnelling or add your local network as an exception. Also make sure AP isolation or client isolation is off for your main network, as that feature deliberately stops devices seeing each other.
Step 3: Note the Printer IP Address
A direct IP connection is more reliable than automatic discovery. You will need the current address to re-add the scanner.
- On the printer, go to Settings, then Network Settings, then Network Status.
- Print the status sheet or connection check.
- Find the IP address, similar to 192.168.1.45.
- Write it down for the next step.
If the address starts with 169.254, the printer has not received a proper address from the router. Reconnect it to Wi-Fi and print the sheet again before continuing.
Step 4: Add the Scanner Again in Epson Scan 2 Settings
Epson Scan 2 keeps its own scanner list, separate from the printer list. That entry can be missing or point to an old address even when printing works.
- Close Epson Scan 2 completely.
- Open Epson Scan 2 Settings from the Epson folder on your computer.
- Delete any old network entry for the same printer.
- Click Add and choose Search for Network Addresses.
- If the printer appears, select it and click OK.
- If it does not appear, choose Enter Address, type the IP address from the status sheet, and click Add.
- Click Test to confirm the connection, then open Epson Scan 2 and try a preview scan.
This step fixes most cases where the router changed the printer address. To stop it recurring, set a DHCP reservation for the printer in your router so it always receives the same address.
Step 5: Allow Epson Scan 2 Through Your Firewall
Firewalls often block the background service Epson Scan 2 uses. The main app may be allowed while the communication service is not.
On Windows, open Windows Security, go to Firewall and Network Protection, and choose Allow an App Through Firewall. Make sure Epson Scan 2 is allowed on Private networks. If you use third-party antivirus with its own firewall, check there instead. On a Mac, go to System Settings, Network, then Firewall, and allow Epson Scan 2 to accept incoming connections.
Temporarily disabling the firewall for one test scan can confirm whether it is the cause, but turn it back on straight away and add the allow rule properly. Our guide on fixing a printer not available error on your home network covers further router and firewall checks that also apply to scanners.
Step 6: Reinstall the Full Driver Package
If the scanner entry will not save or Test always fails on the correct address, the installation may be damaged. A clean install works better than installing over the top.
- Disconnect any USB cable between printer and computer.
- Uninstall Epson Scan 2 and the printer driver.
- Restart the computer.
- Download the latest Full Driver and Software Package for your exact model from the official Epson support and drivers page.
- Run the installer and choose the Wi-Fi or network option, not USB.
- Print a test page, then confirm the network scanner is listed in Epson Scan 2 Settings.
Match the driver to your operating system version. A package for an older version of Windows or macOS can leave the scanner component missing even though printing installs correctly.
Step 7: Check Router Settings That Block Discovery
Some routers block the multicast traffic that discovery relies on, especially after changing provider or enabling new security features.
- AP or client isolation: Turn it off for your main network.
- Guest network: Move both devices off it.
- Band steering: Temporarily separate the 2.4GHz and 5GHz names to test whether devices are being kept apart.
- Mesh firmware: Update it if discovery fails across several devices.
After changing any router setting, restart the printer, print a new status sheet, and re-add the scanner if the address changed. You can also check model-specific help in the Epson frequently asked questions and product support library.
Common Mistakes to Avoid
- Only reinstalling the printer driver: You need the full package that includes Epson Scan 2.
- Testing with a VPN active: Always test with it off first.
- Using an old IP address: Always print a fresh status sheet.
- Skipping the Test button: If Test fails in Settings, the main window will not work either.
- Downloading drivers from random sites: Use only the official package for your exact model.
Conclusion
Epson Scan 2 not finding your scanner is almost always a network visibility problem, not a broken scanner. Restart everything, confirm both devices share the same network, re-add the scanner by its current IP address, and check your firewall. Reinstall the full driver only if those steps fail. Once it works, reserve the printer’s IP address in your router and the problem is far less likely to return.
Frequently Asked Questions
Why can I print but not scan with my Epson printer?
Printing and scanning use different services. A firewall, VPN, or outdated scanner entry can block scanning while printing works. Re-adding the scanner by IP address and allowing Epson Scan 2 through the firewall fixes most cases.
Where do I find my Epson printer IP address?
Print a Network Status sheet from Settings, Network Settings, and Network Status on the printer. The address is listed there. You can also check the attached devices list in your router.
Do I need a USB cable to set up network scanning?
No. You can set up network scanning over Wi-Fi using the full driver package and Epson Scan 2 Settings. USB is only a fallback if Wi-Fi setup keeps failing.
Why does Epson Scan 2 keep losing the scanner after a restart?
The router is likely assigning a new IP address each time. Set a DHCP reservation or static IP for the printer in your router so the software always looks at the same address.
Will reinstalling Epson Scan 2 delete my scanned files?
No. Reinstalling removes the software and may reset custom scan profiles, but files you have already scanned and saved on your computer will not be deleted.


Leave a Reply